WaveRIDER

"The Quality Control Tool No Wave Solder Operator Should Be Without"

Electronics Manufacturing Instruments

     Time and temperature are very important variables in soldering printed circuit boards. It is important to bring the circuit board assemblies up to a high enough temperature for a long enough period to effectively solder the components to the board. Getting the temperature up too high or heating the assembly too quickly can result in component damage. Not heating things up enough results in poor soldering and reliability problems.
     ECD manufactures a variety of instruments to assist you in accurately monitoring the time and temperature variables in your electronics manufacturing processes.

Shown with Expander Rails

• Now ready for NO-Lead
  • New housing and insulation system with 30% more thermal protection
  • New- no lead coupons are available, made from Polyimide, to with-stand the higher soldering temperatures seen in lead free soldering
• Reduces your cost
• Increases yields
• Quick and easy to use- provides printed reports without a computer
• Checks conveyor, solder wave & pre-heat
• WaveRIDER SPC Analysis Software

Operation

The WaveRIDER is run through the wave solder process as one would normally run a printed circuit board through the wave solder machine. After passing through the wave solder machine, the RIDER is connected to a computer with an interface cable. Data captured by the RIDER is transferred to the computer and analized with the SPC tools available and reports generated with no additional equipment requirement.

SuperM.O.L.E. Gold Compatible WaveRIDER Specifications:

Reduces your cost

To ensure optimal equipment performance, you need to know what's actually going on inside the process. Now you can analyze your wave soldering process and fine tune your machine for optimum performance, reducing scrap and rework. Your now have ISO documentation available on critical machine parameters.

Increases yields

The WaveRIDER is the most accurate process monitor for wave solder machines available. Designed to give your manufacturing team the edge they need, the WaveRIDER can increase overall production yields and optimize machine performance.

Quick and easy to use

WaveRIDER's unique design allows operators and maintenance personnel to easily perform routine operation checks and troubleshooting diagnostics in just a few minutes. Quickly measure and print conveyor speed, solder wave and pre-heat parameters.

General Information

The WaveRIDER is a self-contained system that provides critical data on wave solder machine setup and performance. Used in conjuntion with your Gold M.O.L.E.® Temperature Profiler, you can insure your wave solder machine is preforming as it should.

The standard WaveRIDER consists of:

• WaveRIDER pallet (RIDER)
• Manual
• Wave Solder Troubleshooting Expert Guide
• WaveRIDER® SPC Software

Checks conveyor, solder wave & pre-heat

The brain of the system is the SuperM.O.L.E. Gold. The M.O.L.E. records and stores data as the WaveRIDER passes through the wave solder machine. Sensors embedded in the RIDER monitor one or two solder waves. Analytical software in the M.O.L.E. analyzes and generates an accurate report covering:

• Board Contact Lengths
• Board Dwell Time in the Solder Waves
• Board Immersion Depths
• Conveyor Speed
• Conveyor to Solder Wave Parallelism
• Temperature Delta at Solder Wave
• Preheat Minimum and Maximum Temperatures
• Preheat Slope
• Accurate Solder Wave Temperature
• Total Time Spent above Typical Solder Melting Point Temperatures
• Chip Wave Specifications with Automatic Detection

Company| Products & Solutions | News & Events |Apply for job | Download | Sitemap | Contact us

Millennium Hi-Tech Corporation Co., Ltd. © 2006 All rights reserved.
Contact Webmaster for more information

Millennium Hi-Tech Corporation Co., Ltd. 55/39 SoiPrasertmanukit42, Navamin, Bungkum Bangkok 10230
Tel : +66-2508-2051-2 Fax : +66-2508-2053 http://www.millennium-hitech.com  E-mail :surasit@millennium-hitech.com